Determination of the Performance Scores of a Photovoltaic Power Plant Connected to the Grid: The Zagtouli Photovoltaic Power Plant in Burkina-Faso

Photovoltaic solar energy is still in its infancy in Burkina Faso, despite the country’s high solar potential. The electricity grid is experiencing an increase in demand for energy, creating a shortfall in supply. The Zagtouli photovoltaic solar power plant in Burkina Faso is the first milestone in the development of renewable photovoltaic energy, with a rated output of 33.6 Megawatts peak, to strengthen the electricity grid by reducing hydrocarbon consumption. The aim of this work is to evaluate the performance of the plant by proposing a performance score for the Zagtouli plant, which should provide a basis for assessing the performance of a power plant. To meet the objectives, we collected data for three consecutive years of production, from 2019 to 2021. From this data, we used the method based on the calculation of the performance indicators specified by the International Energy Agency (IEA) and described in the standardised norms IEC (International Electrotechnical Commission) CEI61724, and we also carried out a performance classification using the K-Means method. It is clear that with the results obtained for the PR performance index (over 70%), the installation can be classified as one of the best-performing systems. It also emerges that various losses (temperatures on the panels, cabling, partial shading, spectral losses, dirt, and unexpected inverter failures) have a negative impact on the installation’s energy production.

• Solar Energy
• Solar Power Plant
• Climatic Parameters
• Performance

1. Introduction

Burkina Faso is one of the central countries of the Sahel. Burkina Faso has an arid to semi-arid climate, with savannah, but it is also rich in energy resources [1] . It has no proven oil resources, but the sun and wood energy are the main renewable energy resources, with record levels of sunshine. The Zagtouli photovoltaic solar power plant is the first stage in a vast programme to develop photovoltaic energy in Burkina Faso. The plant’s output supplies the entire Zagtouli load-shedding substation [2] . However, the coefficients of performance of the solar panels proposed by the IEC standards make it possible to calculate the performance of the power plant but do not say whether the system is efficient or not [3] . For these reasons, it is important to find a performance score on which we can base the state of performance of the plant by classifying the performance into three classes. To do this, after calculating the different performance coefficients, we will use the K-means method to divide these results into three clusters that will determine the performance of the plant. Cluster 0 identifies a less efficient system, cluster 1 a moderately efficient system, cluster 2 a more efficient system and cluster 2 a very efficient system.

2. Materials and Methods

This section describes the method used to assess the actual performance of the power plant, calculate the parameters required for the analysis, and then simulate the various performance indices in Python.

The performance analysis criteria used are those specified by the International Energy Agency (IEA) and described in the standardised norms (International Electrotechnical Commission) IEC617224. These parameters are field efficiency (Y_a), final efficiency (Y_f), reference efficiency (Y_r), performance ratio (P_R), system losses (L_s) and miscellaneous losses (L_c) [4] - [6] . Various performance indices are used to assess the performance of a solar photovoltaic power plant at actual operating sites. These indicators are physical quantities defined as follows:

$Y_A=\frac{E_{DC}}{P_{PV}}$ (1)

$Y_F=\frac{E_{AC}}{P_{PV}}$ (2)

$Y_R=\frac{S_R}{H_R}$ (3)

$PR=\frac{Y_F}{Y_R}$ (4)

${\eta }_{PV}=\frac{E_{DC}}{S_R\times A_{PV}}\times 100$ (5)

${\eta }_{sys}=\frac{E_{AC}}{S_R\times A_{PV}}\times 100$ (6)

$L_s=Y_A-Y_F$ (7)

$L_c=Y_R-Y_A$ (8)

3. Results

Meteorological stations installed within the power plant were used to measure meteorological parameters. Daily production data recorded every few minutes were used to analyse the PV plant. Figure 1 shows the monthly yields Y_a, _Yf and Y_r for the PV plant from 2019 to 2021.

Figure 1

Figure 1. Monthly change in yield 𝑌 𝑎 , 𝑌 𝑓 , 𝑌𝑟 for the PV plant (2019 to 2021).

Figure 2

Figure 2. Monthly evolution of the PR and the various losses (Ls and Lc) of PV power plants from 2019 to 2021.

Figure 2 shows the monthly evolution of the PR and the various losses (Ls and Lc) of PV power plants from 2019 to 2021.

Figure 3

(a)--(b)--Figure 3. A histogram of shape factors from 2019 to 2021.

Figure 3

(a)--(b)--Figure 3. A histogram of shape factors from 2019 to 2021.

Figure 3 shows a histogram of shape factors from 2019 to 2021.

Figure 4 shows the variation in the daily performance ratio as a function of miscellaneous losses (L_c).

Figure 4

Figure 4. Form factor and other losses (2019).

Table 1 shows the performance score for our power plant for 2019 - 2021.

Table 1

Table 1. Performance scores for the various parameters.

Ya [h/j]	Yf [h/j]	Yr [h/j]	PR [%]	EDC[MWh]	EAC[MWh]	Ls[h/j]	Lc[h/j]	Rond [%]	FC [%]	Irr [KW/m2]	T-air []	HR [kW/m2]	Labels
5.10	5.03	6.76	0.744083	0.051	0.050	0.07	1.66	0.980	0.209	0.199378	28.535533	10.575598	0
5.09	5.02	6.67	0.752624	0.050	0.049	0.07	1.58	0.980	0.209	0.183669	30.186552	9.249461	0
4.44	4.38	6.15	0.712195	0.051	0.050	0.06	1.71	0.980	0.182	0.174488	33.439480	15.772166	0
4.79	4.72	6.09	0.775041	0.052	0.051	0.07	1.30	0.980	0.196	0.178578	35.653133	28.246810	0
4.54	4.46	5.83	0.765009	0.051	0.050	0.08	1.29	0.980	0.186	0.174555	33.740001	46.751950	0
4.41	4.33	5.32	0.813910	0.054	0.053	0.08	0.91	0.980	0.181	0.156456	31.366421	58.532379	2
3.78	3.72	4.56	0.815789	0.055	0.054	0.06	0.78	0.980	0.155	0.131102	28.479273	72.564594	2
4.01	3.94	4.85	0.812371	0.054	0.053	0.07	0.84	0.980	0.164	0.146360	27.668277	78.134820	2
4.95	4.86	6.22	0.781350	0.053	0.052	0.09	1.27	0.980	0.202	0.180646	29.668691	68.503321	0
5.03	4.95	5.91	0.837563	0.055	0.054	0.08	0.88	0.980	0.206	0.181012	30.159880	63.808980	0
5.15	5.07	6.70	0.756716	0.051	0.050	0.08	1.55	0.980	0.211	0.196511	32.699487	26.066612	0
5.13	5.04	6.53	0.771822	0.051	0.050	0.09	1.40	0.980	0.210	0.199834	30.099086	14.095395	0
4.95	4.87	6.10	0.798361	0.053	0.087	0.08	1.15	0.960	0.203	0.189679	27.832732	14.728955	0
5.31	5.14	6.77	0.759232	0.051	0.050	0.17	1.46	0.960	0.214	0.195613	30.722343	10.567386	0
5.61	4.70	6.44	0.798137	0.048	0.049	0.91	0.83	0.950	0.195	0.199342	35.223498	14.321951	0
4.82	4.77	5.78	0.825260	0.053	0.054	0.05	0.96	0.960	0.198	0.173592	34.095271	43.935813	0
4.05	3.99	5.14	0.876265	0.052	0.051	0.06	1.09	0.940	0.166	0.154888	31.381866	56.970551	2
4.33	4.26	5.06	0.841897	0.056	0.055	0.07	0.73	0.960	0.177	0.157868	29.304958	68.487597	2
3.65	3.59	4.40	0.815909	0.054	0.053	0.06	0.75	0.940	0.149	0.136796	27.362050	78.767796	2
4.18	3.86	5.24	0.836641	0.052	0.048	0.32	1.06	0.940	0.161	0.156674	28.304205	75.275771	2
4.72	4.65	6.28	0.740446	0.049	0.048	0.07	1.56	0.950	0.194	0.194994	30.260871	57.990716	0
4.42	4.38	6.66	0.857658	0.043	0.043	0.04	2.24	0.950	0.182	0.199739	31.259815	22.509313	1
4.52	4.45	6.37	0.798587	0.046	0.046	0.07	1.85	0.950	0.185	0.197416	28.720683	22.314937	1
4.87	4.65	6.64	0.700301	0.048	0.046	0.22	1.77	0.950	0.193	0.013789	31.921531	14.065008	0
4.68	4.61	6.76	0.781953	0.045	0.045	0.07	2.08	0.950	0.192	0.175241	31.634608	10.892815	1
4.22	4.16	6.25	0.765600	0.044	0.043	0.06	2.03	0.950	0.173	0.181655	34.339777	15.008603	1
4.20	4.14	6.57	0.730137	0.043	0.041	0.06	2.37	0.950	0.172	0.190142	35.837967	25.932864	1
4.13	4.07	5.75	0.707826	0.042	0.046	0.06	1.62	0.950	0.169	0.173004	33.540007	47.287519	1
3.84	3.77	5.53	0.781736	0.045	0.045	0.07	1.69	0.950	0.157	0.158886	30.467929	62.172921	1
3.57	3.51	4.95	0.790909	0.047	0.046	0.06	1.38	0.978	0.146	0.153480	27.939941	76.402448	2
4.08	4.02	5.80	0.793103	0.044	0.043	0.06	1.72	0.970	0.167	0.174153	29.342994	70.694695	1
4.15	4.09	6.41	0.760655	0.045	0.042	0.06	2.26	0.970	0.170	0.199132	32.047010	55.644902	1
4.28	4.22	6.45	0.754264	0.043	0.043	0.06	2.17	0.950	0.175	0.187972	33.114837	25.423042	1
4.55	4.48	6.02	0.744186	0.049	0.049	0.07	1.47	0.970	0.187	0.185644	30.046331	15.005391	0

4. Discussion

Simulations of the various performance analysis parameters are shown in Figures 1-4 . Figure 1 shows the distribution of monthly field, final and reference yields. The monthly yield of the field (Y_a) varies from 3.57 h/d (July 2021) to 5.61 h/d (March 2020) with an average of 4.506 h/d. The final monthly yield (Y_f) varies from 3.51 h/d (July 2021) to 5.14 h/d (February 2020) and the reference yield (Y_r) varies between a minimum value of 4.4 h/d in August 2020 and a maximum value of 6.77 h/d in the same year. The number of hours of irradiation at the site close to the reference irradiation is approximately 5.9675 h. As for the different losses in Figure 2 , the losses by conversion (L_s) are stable with an average of 0.075 h/d ranging from 0.06 h/d (March, July) to 0.09 h/d (September, November) during 2019. This shows the performance of the field’s inverters in converting DC current into AC current. The same trend can be observed in 2020 (except for March and September, which could be due to a breakdown in some inverters) and in 2021 (except for August), and the various monthly losses (L_c) are highly remarkable, with a minimum of 0.78 h/d and a maximum of 1.71 h/d for 2019. However, the performance ratio fluctuates from month to month. In 2019, it is maintained at an average of 77.82%, varying from 71.21% (March) to 83.75% (October). In June, July, August, September and October 2019, the PR was around 81.22%, and miscellaneous losses L_c were 0.936 h/d. These months appear to be favourable for the operation of the power plant because the temperature is falling, coinciding with the arrival of the rainy season. In the months of November, December, January, February, March, April, May and 2019, there was a considerable drop in PR (75.73% on average) due to huge L_c losses (1.47 h/d). These months are characterised by the presence of hot winds (February, March) leading to dust deposits on the modules and high temperatures (April, May) and in 2020 - 2021 the range during these two years is from 70.03% (January 2021) to 87.62% (June 2020) with an average of 78.49%. Figure 3 also shows the plant’s monthly form factor (FF), i.e., its ability to operate at full power without interruption. In 2019 - 2020, the load factor varied between 14.9% in August 2020 and 21.4% in February 2020, with an average of 18.87% over the two years. The highest average value was reached in the first year (2019) with a FF of 19.25%. It was lower for the months of June, July and August and coincides with the rainy period, which could be explained by the diminution in the number of hours of sunshine. The lowest load factor values during the two production years are recorded for the months of July 2019 and August 2020, at 15.5% and 14.9%, respectively. In the following year, 2021, the load factor is between 4.0% (August) and 19.3% (January), with an average of 15.87%. The rainy months of June and July have values of 15.7% and 14.6% respectively. Figure 4 shows the variation in daily production as a function of the performance ratio in June 2019. We note that the normalised performance ratio is unstable. It varies between 70% (22/06/2019) and 94% (13/06/2019) with an average of 80%. For this month, PR values below 80% correspond to huge miscellaneous losses, with these energy losses generating an average of 0.985 MWh/d. Finally, Table 1 shows the performance scores for the various parameters studied. Visually, the parameters can be separated into three distinct Label groups:

5. Conclusions

It is important to know the performance of the Zagtouli photovoltaic plant after eight years of operation. To do this, we used the method specified by the International Electrotechnical Commission (IEC) and published in the international standard IEC 61724. The results show that the performance ratio is unstable and is more influenced by various losses while throughout the operating period due to environmental conditions (temperature, dust). However, the conversion losses are stable, which explains why the inverters perform satisfactorily. The performance score allowed you to have the following classes:

-Class 0 (less efficient), we have a PR around 76.6%, an average L_C of 1.36 hours/month and L_S around 0.08 hours/month.

-Class 1 (moderately efficient) with an average PR of 77.4%, an Lc of 1.24 h/d and L_s of 0.06 h/d.

-Class 2 (very efficient) with an average PR of 82.5%, an L_c of 0.94 h/d and an L_s of 0.05 h/d.

These results can constitute a basis for evaluating the performance of other PV plants.

We will then be able to compare these results with others obtained on different sites in order to improve the performance grid that we found.

To optimize our system, we can provide an air cooling system, and an automatic fault detection system linked to DC/AC conversion. For future performance analysis studies, software methods like PVUSA Improved and PVsyst could be used.

References

1. https://books.openedition.org/irdeditions/29436

2. Missaoui, R., Ghezal, A. and Hammou, K. (2017) Burkina Faso-Assistance à la mise en place des conditions technico-économiques pour le soutien au développement de la filière photovoltaïque raccordée au réseau. Rapport d’activité 2 et 3. Référence de la mission: CW137.201605 Burkina ARSE.

3. Ayompe, L.M., Duffy, A., McCormack, S.J. and Conlon, M. (2011) Measured Performance of a 1.72kw Rooftop Grid Connected Photovoltaic System in Ireland. Energy Conversion and Management, 52, 816-825. >https://doi.org/10.1016/j.enconman.2010.08.007

4. Elhadj Sidi, C.E.B., Ndiaye, M.L., El Bah, M., Mbodji, A., Ndiaye, A. and Ndiaye, P.A. (2016) Performance Analysis of the First Large-Scale (15 MWP) Grid-Connected Photovoltaic Plant in Mauritania. Energy Conversion and Management, 119, 411-421. >https://doi.org/10.1016/j.enconman.2016.04.070

5. Sundaram, S. and Babu, J.S.C. (2015) Performance Evaluation and Validation of 5mwp Grid Connected Solar Photovoltaic Plant in South India. Energy Conversion and Management, 100, 429-439. >https://doi.org/10.1016/j.enconman.2015.04.069

6. Niang, S.A.A., Drame, M.S., Sarr, A., Toure, M.D., Gueye, A., Ndiaye, S.O., et al. (2024) Seasonal Performance of Solar Power Plants in the Sahel Region: A Study in Senegal, West Africa. Smart Grid and Renewable Energy, 15, 79-97. >https://doi.org/10.4236/sgre.2024.152005

7. Ndiaye, A., Aidara, M.C., Mbaye, A. and Ndiaye, M.L. (2023) Study of the Impact of Grid Disconnections on the Production of a Photovoltaic Solar Power Plant: Case of Diamniadio Power Plant. Journal of Power and Energy Engineering, 11, 16-25. >https://doi.org/10.4236/jpee.2023.116002

8. Sharma, V. and Chandel, S.S. (2013) Performance Analysis of a 190 KWP Grid Interactive Solar Photovoltaic Power Plant in India. Energy, 55, 476-485. >https://doi.org/10.1016/j.energy.2013.03.075

9. Tripathi, B., Yadav, P., Rathod, S. and Kumar, M. (2014) Performance Analysis and Comparison of Two Silicon Material Based Photovoltaic Technologies under Actual Climatic Conditions in Western India. Energy Conversion and Management, 80, 97-102. >https://doi.org/10.1016/j.enconman.2014.01.013

10. Balaska, A., Tahri, A., Tahri, F. and Stambouli, A.B. (2017) Performance Assessment of Five Different Photovoltaic Module Technologies under Outdoor Conditions in Algeria. Renewable Energy, 107, 53-60. >https://doi.org/10.1016/j.renene.2017.01.057

11. Jamil, I., Zhao, J., Zhang, L., Jamil, R. and Rafique, S.F. (2017) Evaluation of Energy Production and Energy Yield Assessment Based on Feasibility, Design, and Execution of 3×50 MW Grid-Connected Solar PV Pilot Project in Nooriabad. International Journal of Photoenergy, 2017, 1-18. >https://doi.org/10.1155/2017/6429581

12. Sharma, R. and Goel, S. (2017) Performance Analysis of a 11.2 KWP Roof Top Grid-Connected PV System in Eastern India. Energy Reports, 3, 76-84. >https://doi.org/10.1016/j.egyr.2017.05.001

13. 22©2016-2017—Younes BENZAKI. >https://mrmint.fr

14. de Younes, B. (2018) Comment traiter les données manquantes en Data Science Implémentation du clustering des fleurs d’Iris avec l’algorithme K-Means, Python et Scikit Learn. >https://mrmint.fr/kmeans-python-scikit-learn